More controlled treated-water quality
RO may help reduce dissolved-solids variation where broader treatment is technically required.
Pentair Everpure Commercial RO
Consistent treated water for demanding commercial operations
Get an application-led Everpure MDRO recommendation based on your feed-water quality, required output, connected equipment and operating demand.
Request Commercial RO AssessmentShare your water report, application and required output. Aquainwent will review the complete treatment requirement before recommending a system.
Is your current water treatment meeting commercial demand?
- 1High or changing feed-water TDS
- 2Existing RO output falls short during peak operation
- 3Multiple equipment points require one controlled water supply
- 4Tanker, borewell or mixed-source water changes over time
- 5Repeated membrane or cartridge problems
- 6Inadequate pre-treatment
- 7Incorrect storage or distribution planning
- 8New project without a complete RO design
- 9Uncertainty about whether RO is required at all
Quick fit
Is a commercial MDRO assessment relevant for your site?
- You require treated water for several commercial equipment points
- Your feed-water TDS is high or unstable
- Your present RO cannot meet peak demand
- You are planning a new café, hotel, restaurant or QSR
- You are replacing an existing commercial RO
- You need help with pre-treatment, storage or distribution
- You are unsure whether filtration, softening or RO is appropriate
Final system fit depends on water testing, required output, operating demand and site utilities.
Commercial design priorities
Why application-led commercial RO design matters
Output sized around actual demand
System selection should consider peak hourly demand, daily consumption, storage and simultaneous equipment use.
Complete treatment-train review
Aquainwent reviews pre-treatment, MDRO, storage, distribution and application-specific post-treatment.
Support for multiple equipment points
A properly planned system may support several commercial applications when combined demand and distribution are correctly assessed.
Project and consultant support
Aquainwent can review water reports, equipment schedules and site requirements before specification.
Genuine filter and membrane planning
Replacement planning should be based on approved components, feed-water conditions and operating demand.
Treatment choice
RO is not automatically the right treatment for every site
The correct route starts with the water report and the required treated-water quality, not a model number.
Commercial filtration may be enough
Where dissolved-solids reduction is not required, Aquainwent may recommend commercial filtration rather than RO.
- Sediment or particulate
- Chlorine
- Taste or odour
Softening may be required
Softening may be considered when hardness and scale are the primary concerns.
- Reduces calcium and magnesium hardness
- Does not reduce TDS like RO
- May be part of RO pre-treatment where verified
RO may be required
RO may be considered where broader dissolved-solids reduction or one controlled treated-water supply is needed.
- High or unstable feed-water TDS
- Dissolved-mineral composition affects the application
- Controlled supply for connected commercial points
Final treatment selection depends on water testing and the required treated-water quality.
Technical fit
Correct MDRO sizing starts with water quality and real demand
Aquainwent reviews the inputs that determine treatment, output, storage, distribution and site fit.
Source-water profile
Source, TDS, hardness, alkalinity, chlorine and turbidity.
Relevant contaminants
Iron, manganese and silica where the source or application makes them relevant.
Required water quality
Equipment, beverage, ingredient-water and application-specific targets.
Peak demand
Hourly draw, simultaneous equipment flow and number of connected points.
Daily demand
Daily treated-water volume, operating hours and current treatment performance.
Storage and distribution
Tank requirement, boosting, delivery pressure and distribution route.
Reject-water planning
Verified recovery, discharge route, drainage and site-specific management.
Utilities and access
Feed pressure, electrical supply, space, service clearance and commissioning date.
Verified model comparison
MDRO-800 or MDRO-1600?
Compare current Pentair document values, then assess source water, demand and the complete treatment train before selection.
Pentair Everpure
MDRO-800
2 LPMRated purification flow
W320 × D268 × H598 mmSystem dimensions
3/8 inchInlet / outlet
0.1–0.4 MPaRecommended inlet pressure
May be considered when…
The verified output, assessed feed water, duty and engineered storage/distribution arrangement meet the site requirement.
View complete verified specifications
- Rated purification flow
- 2 LPM
- Rated total purified-water volume
- 9 m³
- Dimensions
- W320 × D268 × H598 mm
- Inlet / outlet
- 3/8 inch
- Recommended inlet pressure
- 0.1–0.4 MPa
- Operating pressure
- 0.6–0.9 MPa
- Inlet-water temperature
- 5–38°C
- Rated power
- 108 W
- Water-efficiency rating
- Level 1
- Phosphate cartridge
- PPC-80
- RO cartridge
- MRO-800
- Brochure-recommended cycles
- PPC: 12–24 months; RO: 12–18 months
Pentair Everpure
MDRO-1600
4 LPMRated purification flow
W320 × D268 × H708 mmSystem dimensions
3/8 inchInlet / outlet
0.1–0.4 MPaRecommended inlet pressure
May be considered when…
Higher combined commercial demand requires the verified output and the assessed feed water, duty, storage and distribution design support its use.
View complete verified specifications
- Rated purification flow
- 4 LPM
- Rated total purified-water volume
- 12 m³
- Dimensions
- W320 × D268 × H708 mm
- Inlet / outlet
- 3/8 inch
- Recommended inlet pressure
- 0.1–0.4 MPa
- Operating pressure
- 0.6–0.9 MPa
- Inlet-water temperature
- 5–38°C
- Rated power
- 216 W
- Water-efficiency rating
- Level 1
- Phosphate cartridge
- PPC-160
- RO cartridge
- MRO-1600
- Brochure-recommended cycles
- PPC: 12–24 months; RO: 12–18 months
Final selection depends on feed-water quality, peak demand, daily volume, verified recovery, duty, storage and distribution design. Published rated values do not establish site suitability on their own.
Complete treatment train
A commercial RO project is more than the RO system
The sequence is a planning framework. The final components depend on the water report, application and site.
Water assessment
Source and target quality
Pre-treatment
Selected from verified need
Everpure MDRO
Model sized to demand
Treated-water storage
Bridges production and draw
Distribution or boosting
Flow and pressure review
Post-treatment
Application-specific
Monitoring and maintenance
Planned lifecycle support
The final treatment train may include sediment filtration, carbon treatment, softening, other verified pre-treatment, storage, boosting, UV or post-RO mineralisation depending on the water report and application. Not every component is mandatory for every site.
Applications
Commercial applications considered for MDRO
Each application requires its own demand and treated-water review. One RO-water specification should not be assumed across every point.
Coffee and espresso
- Why it may matter
- Ingredient-water consistency can influence the beverage programme.
- Demand input
- Machines, peak drinks, water recipe and source water.
- Post-treatment
- Mineralisation or polishing may need review.
Tea and beverage chains
- Why it may matter
- A controlled ingredient-water supply may support repeatability.
- Demand input
- Dispensers, recipes, peak volume and operating hours.
- Post-treatment
- The application target must be confirmed.
Ice-machine ingredient water
- Why it may matter
- Dissolved-mineral composition may affect the ice application.
- Demand input
- Machine demand, storage and simultaneous loads.
- Post-treatment
- Final fit requires equipment review.
Commercial drinking water
- Why it may matter
- A controlled treated-water supply may be required at multiple points.
- Demand input
- Peak users, daily demand and distribution route.
- Post-treatment
- Mineral and microbiological requirements need review.
QSR and restaurants
- Why it may matter
- Several beverage or ingredient points may share treatment.
- Demand input
- Equipment schedule, peak service and kitchen demand.
- Post-treatment
- Point-specific polishing may be required.
Hotel back-of-house
- Why it may matter
- Selected ingredient-water points may require controlled TDS.
- Demand input
- F&B outlets, equipment, peak demand and utilities.
- Post-treatment
- Each outlet requires fit review.
Cloud kitchens
- Why it may matter
- Central treatment may support multiple production points.
- Demand input
- Daily volume, recipes, shifts and planned growth.
- Post-treatment
- Final treatment depends on use.
Multi-point beverage systems
- Why it may matter
- A managed treatment backbone may serve several connected loads.
- Demand input
- Combined loads, simultaneity, storage and pressure.
- Post-treatment
- Distribution and point needs must be engineered.
Engineered installation
What must be planned before MDRO installation?
MDRO is engineered commercial RO equipment. Final installation, utilities and commissioning must follow the approved system documentation and project design.
- Verified feed-water conditions
- Inlet plumbing
- Required pre-treatment
- Electrical supply
- Drainage
- Reject-water discharge
- Treated-water storage
- Booster or distribution arrangement
- Installation footprint
- Service clearance
- Membrane and filter access
- Technical commissioning
- Monitoring
- Replacement planning
Aquainwent support
Why commercial teams work with Aquainwent
Aquainwent supports application-led Pentair Everpure commercial RO selection and lifecycle planning in India.
Pentair Everpure product access
Commercial MDRO systems and genuine replacement components.
Water-test and demand review
Selection based on source water, required quality and operating load.
Pre-treatment and storage guidance
Planning the wider treatment train around the application.
Consultant and project support
Technical review before model and configuration decisions.
Installation coordination
Coordination around utilities, site conditions and commissioning.
Filter and membrane support
Approved-component and replacement planning.
Distribution review
Storage, boosting and simultaneous-demand considerations.
Lifecycle planning
Monitoring, service access and maintenance planning.
Consultant and project support
Technical support for consultants and commercial projects
Share the available project information through the same commercial RO assessment. Aquainwent can support the product and application review while the appointed project team retains design responsibility.
- Water-test review
- Demand calculation
- Treatment-train review
- Model selection
- Equipment-schedule review
- Pre-treatment review
- Storage review
- Distribution-flow review
- Reject-water planning
- Connection and utility review
- Installation-footprint review
- Specification wording
- Technical submittals
- Commissioning coordination
- Filter and membrane planning
Objection handling
Questions before selecting a commercial RO system
Does every commercial site need RO?
No. The correct treatment may be filtration, softening, RO or a combined treatment train depending on the water report and required treated-water quality.
What is the difference between MDRO-800 and MDRO-1600?
The models differ in verified output and technical configuration. Final selection depends on feed-water quality, peak demand, duty, storage and distribution—not model size alone.
Can one MDRO supply several pieces of equipment?
It may be possible when the system, storage and distribution are correctly sized for combined peak and daily demand.
Does RO remove hardness?
RO can reduce a broad range of dissolved substances, but feed-water hardness may still require pre-treatment to protect the membrane and support reliable operation.
Does RO remove microorganisms?
RO is not a substitute for a complete microbiological-control strategy. UV or other treatment may be required depending on the water source and application.
Is pre-treatment required?
Pre-treatment depends on the feed-water condition and MDRO requirements. Sediment, chlorine, hardness, iron or other concerns must be reviewed before finalising the treatment train.
Will mineralisation be required after RO?
Some beverage and ingredient-water applications may require application-specific post-treatment or mineralisation. This should be determined from the equipment and water-quality requirement.
How much reject water will the system produce?
Reject-water volume depends on the verified system recovery, feed-water condition and operating configuration. A value should not be stated without approved technical data.
How often will filters and membranes need replacement?
Replacement depends on water quality, pre-treatment, operating demand and approved component guidance. Aquainwent will recommend a monitoring and replacement plan.
Why is pricing not shown?
The final system, pre-treatment, storage, installation and commissioning scope depend on the complete commercial application.
Commercial RO Water Assessment
Request Your Commercial RO Assessment
Share your feed-water quality, required output and application. Aquainwent will review the complete requirement before recommending an MDRO or alternate treatment configuration.
- Feed-water and treatment review
- Peak, daily and simultaneous-demand review
- Pre-treatment, storage and distribution review
- MDRO or alternate treatment recommendation
Not sure which commercial RO configuration fits your site?
Share your water report, required output and connected equipment. Aquainwent will help identify the appropriate next step.
-->
-->